Technical article

Why is my silicone rubber not curing? Six root causes

Before you add more catalyst, rule out the six causes that account for most addition-cure failures — from poisoning to mixing order.

Technical 8 min read18 September 2026

An addition-cure silicone compound that stays soft, tacky or unevenly cured after the oven is rarely a catalyst quality problem. In most investigations the platinum is doing exactly what the formulation asks of it, and something upstream has changed: a contaminant, a mixing step, a dosage or a temperature. Before ordering a different grade or raising the platinum loading, work through the six conditions below. Each one can be checked with material already on site, and each one is cheaper to test than a reformulation.

Start with the variables you can measure

Three explanations account for a large share of apparent curing failures: the catalyst and inhibitor were added in the wrong order, the batch never reached the cure temperature, or the inhibitor was overdosed for the working time that was wanted. Check these before anything more elaborate. Confirm the drum was shaken before dispensing, confirm the catalyst was weighed rather than estimated, and confirm the part temperature with a thermocouple rather than by reading the oven display.

The six root causes

The list below is ordered by how often each cause shows up in a production investigation, not by how difficult it is to fix.

  1. Catalyst poisoning. Trace sulfur, phosphorus, nitrogen or heavy metals deactivate the platinum complex. The compound may look and smell normal and still fail to cross-link.
  2. Mixing order. The inhibitor should be dispersed in the base before the catalyst is added. When catalyst and inhibitor meet as concentrates, local inhibition can leave soft pockets in an otherwise cured part.
  3. Inhibitor overdose. A longer pot life is bought with inhibition. Above the correct dosage the compound may cure only at the surface, or stay tacky in thick sections.
  4. Concentration mismatch. The dosage may sit below the 0.05%–0.5% working range, or the catalyst lot may differ from the one the formulation was validated on.
  5. Cure temperature shortfall. Thick sections, cold moulds, fast line speeds and large thermal mass can keep the part below the activation window even when the oven reads correctly.
  6. A change in the base. A new silicone lot, a different filler treatment, a pigment change or recycled filler can adsorb the catalyst or introduce a poison, so the formulation that worked last month no longer cures.

Why poisoning is so easy to miss

Poisoning does not usually produce a completely liquid batch. It produces a batch that starts to cross-link and then stalls, cures only where it touched the hot mould, or varies from part to part within the same shot. Because nothing in the appearance or viscosity changes, the catalyst is blamed first. The contaminant, however, usually enters with a mould release agent, a cleaning solvent, a packaging material, a pigment or a glove.

A diagnostic sequence

Run the checks in this order. The first four separate a formulation fault from a process fault; the last two confirm the mechanism.

CheckHow to run itWhat it rules out
Control batchSame base and inhibitor, fresh catalyst, no additivesA bad catalyst lot or contaminated base
Mixing orderRepeat with inhibitor dispersed first, catalyst added lastDispersion and local-inhibition effects
Oven profileThermocouple at the part core, not the oven probeA cure-temperature shortfall
Inhibitor ladderHalve the inhibitor dosage in one small trialInhibitor overdose
Catalyst ladderRaise dosage within 0.05%–0.5% and compare cure onsetA concentration shortfall
Contamination auditReview gloves, release agents, solvents and packagingExternal sulfur, phosphorus and nitrogen sources

What not to do first

Raising the catalyst dosage is the most common first response, and it is the one that hides evidence. A batch that cures only at a much higher dosage is telling you the platinum is being consumed or blocked, not that platinum was missing. If the underlying poison is not identified, the next batch will fail in the same way, and the elevated dosage becomes the new baseline until the process drifts again.

A control batch made with a known-good base, a standard grade such as PC-11 and no additives is the single most useful experiment. If the control cures, the catalyst is not the variable that changed. If it does not, the problem is in the catalyst or the base, and the conversation moves to the material rather than the line.

Rule out before reformulating

Changing grade cannot fix a cold mould, a sulfur-contaminated glove or an inhibitor dosed far above the intended level. Measure those three first; they cost nothing to check.

Once the cause is understood, the right response is usually smaller than expected: correct the mixing order, re-weigh the inhibitor, clean a mould, or move to an anti-poisoning grade such as PC-18B where the contamination cannot be removed. PC-18A, the second-generation anti-poisoning grade, is under final R&D and available for evaluation samples only.

Next step

From article to evaluation sample

If this article describes your process, request a sample of the recommended grade with the matching inhibitor. Evaluation quantities ship in 5–7 days.

Technical reply within 24 hours
Evaluation samples in 5–7 days
COA, TDS and SDS on request
Custom concentration 1,000–20,000 PPM