Stable cure where the chemistry fights back.
Anti-poisoning catalysis for potting, encapsulation and high-voltage insulation, where contaminants and thick sections defeat ordinary catalysts.
Where the process breaks down.
Potting and high-voltage insulation are hostile to a platinum catalyst. Sulfur, phosphorus, nitrogen and heavy-metal traces on boards, housings and inserts deactivate the active centre, and the failure is not obvious until the pot is opened. Thick sections add a second problem: cure proceeds from the outside in, so a fully cured skin can hide a soft core.
A failed pot cannot be reworked. The part, the labour and the schedule are all lost, which is why anti-poisoning chemistry is specified before the first production run rather than after a failure.
What the defect looks like.
- Sulfur, phosphorus, nitrogen and heavy-metal traces on boards and housings poison the catalyst
- Thick sections cure unevenly, leaving soft cores and stressed interfaces
- A failed pot cannot be reworked; the part and the labour are both lost
What the formulation needs.
PC-18B retains activity with slight to moderate poisoning agents. PC-18A, currently under final R&D, targets high concentrations of multiple contaminants and is available for evaluation. PC-50 handles thick-section heat exposure.
The sequence that works is to identify the contamination source before raising dosage. PC-18B retains stable vulcanisation activity with slight to moderate poisoning agents. PC-18A, under final R&D, targets high concentrations and multiple contaminant types and is available for evaluation samples only.
For thick sections, PC-50 combines stability above 150°C with a 5–50 cP viscosity for uniform dispersion and gelation. PC-611 or PC-612 keeps the mixed batch workable through the potting window, and the upper half of the 0.05%–0.5% dosage range is usually the starting point for anti-poisoning grades.
PC-18A is under final R&D. Evaluation samples are available for contaminated-system trials; commercial supply is not yet committed. PC-18B is the production grade for slight to moderate poisoning, and PC-50 covers thick-section heat exposure.
How the first evaluation is run.
- Start from PC-18B unless the failure mode points to another grade.
- Hold catalyst dosage at the lower bound of 0.05%–0.5% and fix the inhibitor dose.
- Run the customer acceptance test on the cured part, not on the liquid mix.
- Change one variable per run: grade, dosage or inhibitor.
What the numbers behind this page show.
Grades most often specified for Encapsulation.
Each card opens the grade page with full specification, packaging, shelf life and inhibitor pairing. Evaluation quantities are available across the range; the one exception is stated below.
Custom (1,000–20,000 PPM)
First-generation anti-poisoning catalyst. Retains stable vulcanisation activity in environments with slight to moderate poisoning impurities — trace sulfur, phosphorus and nitrogen compounds.
Custom (1,000–20,000 PPM)
Second-generation anti-poisoning catalyst, engineered against high concentrations and multiple contaminant types. Under final R&D: available for evaluation samples, with commercial supply not yet committed.
Custom (1,000–20,000 PPM)
Ultra high-temperature grade with a low-viscosity profile (5–50 cP) for easy dispersion. Remains stable above 150°C for long dwell times, for thick sections and hot-running parts.
PC-18A is under final R&D. It is available as an evaluation sample for contaminated-system trials; commercial supply is not yet committed. It is not a production grade today.
Settings for the first trial.
Typical starting parameters for Encapsulation. Treat them as a trial configuration rather than a fixed recipe: the final values depend on the substrate, the equipment and the acceptance test.
| Parameter | Guidance |
|---|---|
| Catalyst dosage | 0.05%–0.5%; anti-poisoning grades may need the upper half |
| Inhibitor | PC-611 / 612 to keep mixed batches workable |
| Thick sections | Stage cure or use low-viscosity PC-50 for uniform gelation |
| Contamination | Identify the poisoning source before raising dosage |
Add base and inhibitor first, then the catalyst. Do not allow direct contact with hydrogen-containing silicone oil or pure inhibitor before mixing. Shake the container before use, and keep drums sealed at 5–15°C away from direct light.
How this looks on a production line.
Measured outcomes for this application, with the challenge and the test conditions stated. Results are customer production data where noted; accelerated aging results name the comparison catalyst.
Practical questions before a trial.
The questions that come up most often when this application moves from specification to a first sample run.
Which grade should we evaluate first for Encapsulation?
PC-18B or PC-18A is the usual starting point. Start at the lower end of the 0.05%–0.5% dosage range and confirm the cure against your own oven before adjusting.
How do we control pot life without slowing the cure?
PC-611 / 612 to keep mixed batches workable. The inhibitor sets working time; the catalyst sets cure speed once the part reaches temperature. Change one of them at a time.
Is PC-18A available for production?
Not yet. PC-18A is under final R&D and is supplied as evaluation samples only; commercial supply is not committed. For production, PC-18B is the anti-poisoning grade, with PC-50 for thick sections that also see heat above 150°C.
Trial Encapsulation with a paired sample set.
Send the cure temperature, the failure you are seeing and the acceptance test. We reply with a recommended grade, platinum concentration and inhibitor pairing, plus a sample plan for the first run.